Anthro Fit Console Unit Handbuch PDF herunterladen

Questions?

1-800-325-3841

Anthro

Corporation Technology Furniture

10450 SW Manhasset Drive Tualatin, Oregon 97062 anthro.com

SAVE THESE INSTRUCTIONS!

Rev. F January 2006

Hello! Thank you for choosing Anthro.

Before beginning assembly of your Console Unit, take a moment to review the parts listed on the next page

to verify that your shipment is complete.

Please review the assembly instructions of all Anthro products you

purchased and are planning to include in this installation, prior to beginning this assembly.

Your Console Unit is heavy!

A second person will be needed for this assembly procedure.

To make the assembly of your Console Unit even easier, we have included all of the required tools. The handy

Hex Driver Bit can be used in your electric drill in place of the Hex Driver.

Hex Driver

”

............................................................

375-5000-00

Hex Driver Bit

”

.....................................................

375-5003-00

Hex Key

”

.................................................................

375-5016-00

Hex Key

”

..................................................................

375-5024-00

3-Way Wrench

.............................................................

225-5196-03

8 oz. Rubber Mallet

.....................................................

375-5022-00

Console Unit

Assembly Instructions

1-800-325-3841

Step 15

Begin by placing the Base Tube Assembly

(Locking Casters

as shown)

onto the Vertical Legs.

Attach the Base Tubes to each Leg by inserting a

ﬁ t

Bolt through a Tube Washer, then insert the

ﬁ t

Bolt

through the Base Tube and carefully thread into

each Vertical Leg.

Tighten all

ﬁ t

Bolts and Cap Screws.

Step 16

(uses the

” Hex Key)

Carefully rotate your Console Unit onto the Casters.

Pop the six Small End Caps into the Leg ends.

Congratulations!

Your assembly is complete.

(

-18 X 3.5”)

ﬁ t

Bolt

325-5194-00

ﬁ t

Tube Washer

225-2050-00 or 225-3522-00

ﬁ t Tube Washer

Locking Casters

Small End Caps

Adjust the Caddy Shelf height by:

1. Squeezing and holding the Paddle.

2. Reposition the Caddy to the desired location.

3. Release the Paddle.

Rotate Knob to

adjust Caddy

angle.

Squeeze Paddle

to adjust Caddy

height.

angle.

Adjust the Caddy Shelf angle by:

1. Rotating the Knob counterclockwise.

2. Reposition the Caddy to the desired angle.

3. Rotate the Knob clockwise.

Adjusting your Console Caddy

1 2 3 4

Inhaltsverzeichnis

Seite 1 - Assembly Instructions

R Questions?1-800-325-3841AnthroCorporation Technology Furniture® 10450 SW Manhasset Drive Tualatin, Oregon 97062 anthro.

Seite 2 - Step 14

AnthroCorporation Technology Furniture® 10450 SW Manhasset Drive Tualatin, Oregon 97062 1-800-325-3841anthro.com18– 3” Non-Locking Casters .

Seite 3 - DETAIL VIEW

Step 9Insert two End Caps into the ends of both 21” Base Tubes. Install two Caster Inserts into each Base Tube and secure with one Insert Screw per In

Seite 4

3/4” Wood Screw325-5106-00Support Screw325-5010-00AnthroCorporation Technology Furniture® 10450 SW Manhasset Drive Tualatin, Oregon 97062 1-

Kommentare zu diesen Handbüchern

Keine Kommentare

Anthro Fit Console Unit Handbuch

Stöbern Sie online oder laden Sie Handbuch nach Computertische Anthro Fit Console Unit herunter. Anthro Fit Console Unit Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Computertische Anthro Fit Console Unit